Clik here to view.
Can't find custom property I added in drop down list to allow me to "group...
I created a custom property which I planned to populate with a value which would distinguish it and allow me to choose this particular node to run my config change template on. However when I go to...
View ArticleRe: Can't see any interfaces in NCM managed devices
Hi Amir, I'm not sure what should be fixed. You have to update NCM inventory in order to have the interfaces available for config change templates. Regards,Jiri
View ArticleRe: Can't see any interfaces in NCM managed devices
Hi Jiri, thanks for response, i thought it should be possible to update the inventory from the Orion Web Console, but i can only update the inventory from the Solarwinds Configuration Manager.When i...
View ArticleConnection refused during Cisco config download
I am using NCM7.2.2 to download a cisco switch config from the web console. When I go try to download it, I get the message that the connection was refused the by the switch IP address. I have tried...
View ArticleRe: Question about install steps from NCM Admin Guide
We performed the integration install on Friday. It installed just fine without any errors. We just had to make sure we pointed it to the existing NCM database. We are planning on upgrading it to...
View ArticleRe: Connection refused during Cisco config download
Hi 1ashgarg, Have you configured the device in NCM to use the same protocol (telnet/SSH) and port as in Engineering toolset? Regards,Jiri
View ArticleClik here to view.
Re: Can't see any interfaces in NCM managed devices
Amir, Actually you can update inventory in NCM Web Console: Regards,Jiri
View ArticleRe: Switching to polling engine NCM 7.2.2 job execution.
I'm confused about the same problem. My jobs scheduled on the main Orion only seem to cover nodes polled there, but when I go to edit jobs on the Poller I get taken to the web console for the main...
View ArticleClik here to view.
Re: Switching to polling engine NCM 7.2.2 job execution.
Jenya, The main Orion web console controls all jobs so no need for additional web consoles. Before NCM 7.2 jobs used the windows task scheduler vs the Orion job engine which meant that jobs had to be...
View ArticleRe: Can't see any interfaces in NCM managed devices
Hi Jiri, i didn't expect it finding the inventory under reports. I will try it with new discovered devices and give feedback. ThanksAmir
View ArticleRe: Connection refused during Cisco config download
The NCM devices were discovered using SNMPv3, and Engineering toolset also used SNMPv3. Do I need to change the device information?
View ArticleRe: NCM connection refused
shawn_b, I am having the same issue with my Cisco switch. I'm using SNMPv3 which passes the test, but do I also need to set up a connection profile?
View ArticleRe: BGP Interface Down View (to crate)
Hi! I yet created a new custom poller based on my OID but i don't say how to create alerts and reports based on UnDP.Can you help me please?
View ArticleRe: NCM connection refused
1ashgarg, yes you do The connection profile is what NCM uses to login to your switch. During automated or manually initiated tasks such as upload\download config, NCM needs to login to the switch in a...
View ArticleRe: NCM connection refused
Bit of confusion here - NCM will use whatever connection profile you set to download configs, config change templates, etc. In the case of the screen shot above, that would be telnet. (I would...
View ArticleClik here to view.
Re: Connection refused during Cisco config download
It looks like you are trying to download your configs with the login credentials and not SNMP. It looks like youe default login is trying to use Telnet to log in. Either change it to SSH if you block...
View ArticleNCM jobs
Since upgrading NPM and NCM recently, I have not been able to run my jobs. I get an error message - "ERROR: Unable to retrieve EngineID". My devices are all there and I can download, upload configs but...
View Article