Clik here to view.
Re: Config changes showing tons of "blank line changes"
You can change the protocol settings by editing the node properties: Jiri
View ArticleRe: Solarwinds Inventory with NCM
Hi, Generally yes, but individual inventory reports may be applicable only to certain vendors or models.The inventory is collected over SNMP; if some device doesn't respond to certain OIDs, these...
View ArticleRe: Cisco VPN Concentrator 3005 Config pull timeout
Hi joetech, Menu-based devices may be tricky. Please consider opening a support case. Regards,Jiri
View ArticleRe: Audit NCM configuration changes
Hi, No, NCM currently doesn't audit settings changes.However if each user is given a unique Orion account, you may be able to narrow down the set of suspects. Regards,Jiri
View ArticleRe: Config changes showing tons of "blank line changes"
OK -- but is that the protocol used to transfer the config FROM the device to NCM, or from NCM to the TFTP server running on the Orion server? We don't have TFTP configured on the firewall. Again, this...
View ArticleRe: Config changes showing tons of "blank line changes"
That protocol is used for both directions. If TFTP is a problem, you can use SCP. Actually, the protocol may have impact on the blank lines as explained by bene above. Are you sure that the command...
View ArticleClik here to view.
Comparison Criteria
Good Afternoon All - I'm trying to set up a few REGEX patterns, and nothing seems to be working correctly. I have tried everything from:^[ \t\r\n\v\f]^service internal[ \t\r\n\v\f]*^service...
View ArticleClik here to view.
Re: NCM changes less than desirable
I agree with Mark's comments on the new features of NCM, Sure we can create 20 different custom properties, but we didn't have to do that with previous version... Mark, pretty sure you figured it...
View ArticleConfig template customization
Hi I would like to customize the default template named "Configure Interfaces Based on Description Cisco IOS" to match for switchport interface configuration instead of interface description. For...
View ArticleNCM without NPM?
Hello Is it possible to use only NCM without purchasing NPM? Or is having NCM dependent on having NPM? ThanksAmy
View ArticleClik here to view.
Re: NCM Script to pull configs through a Firewall?
Mike, What you describe (connecting via a jump-box) is a feature request. Not possible with NCM now. Regards,Jiri
View ArticleRe: NCM Script to pull configs through a Firewall?
Ok thanks, I won't waste anymore time trying to figure it out then Mike
View ArticleRe: NCM Script to pull configs through a Firewall?
Makes sense. There's no workaround. Jiri
View ArticleRe: DHCP Snooping Script
weberam24If you can run a command on each device, and display the information you want to see, then you can just turn that into a job.I have a job that goes out to 700+ Occam DSLAM blades every morning...
View ArticleRe: DHCP Snooping Script
weberam24After re-reading your post, I think I may have provided you an answer to a question you did not ask. I will leave my initial response, just in case, but I am fairly confident, now, you are...
View ArticleRe: Juniper SA / MAG SSL VPN config backup - is there a way with NCM
I am the Community Manager for Backbox.co, and I would like to introduce myself to the Thwack community. If you have any questions about our backup, restoration, recovery and device management...
View ArticleRe: Any NCM v6.0 upgrade gotchas?
wondering what other tool you might be using to deploy configs to multiple devices at once. I find NCM also very useful for compliance.. ie. to find which devices are configured with incorrect snmp...
View ArticleRe: Pushed templates from Configuration management is not seen in the target...
if you see your changes in the startup config, they must be in the running config.... "wr" copies the running config to startup.
View ArticleClik here to view.
Config change report does not ignore nvram or certificates
Hey guys, I am having a problem where the config change report is not ignoring the following: ! Last configuration change at 17:37:32 EDT Tue May 6 2014 ! NVRAM config last...
View Article