Clik here to view.
Re: Can you make variables in a configuration change template optional?
HolyGuacamole is absolutely correct. I used the word none instead of dummy, but here is the actual template that I used: script BaseChangeTemplate( NCM.Nodes...
View ArticleRe: Re: Connection Refused by IP
Hi Holy,In trace it says " Connected! Invalid username or password reported by server, or bad private key." What username or password that i must check?Really appreciate your help
View ArticleRe: Cannot pull config's from Adtran TA5000's
SolarWinds got back with me and placed a pause before the enable command. Here are the two lines of code that I entered for a new Device Template called Adtran_No_Enable. <Command...
View ArticleAlerts after NPM Migration
I have recently migrated a Solarwinds Server from on VM to another. After the migration the customer alerts I had configured made it through the migration but the Custom Properties I use in the alerts...
View ArticleRe: Alerts after NPM Migration
I'd recommend rerunning the configuration wizard. Also, after you configured the system, did you move all the nodes to the new poller and remove the old server? That may be playing a part in it as well.
View ArticleClik here to view.
Re: Alerts after NPM Migration
Configuration Wizard did not work. Trying to figure out how to get my Custom Properties to show up in the Advanced Alert configuration window.
View ArticleClik here to view.
Re: Where can I get a device template for a Cisco ASA 5520 that will give me...
Thanks sixmill. That definitely seems like it would work. I will edit and post the results after the next scheduled job runs.
View ArticleRe: Recommend NCM on Spread the Word for a $25 Amazon gift card!
I have been tasked to look for a Configuration Manager for our network. For years, we have been copying the configure and save it in TFTP server. It is no longer a good practice in today robust and...
View ArticleView limit in NPM/NCM setup
Hi When you install new NCM to NPM setup.How do I limit some user from NCM pages?Can I do that with CP like in NPM? Like NCM_ACCESSYES /NO /SJA
View ArticleClik here to view.
Re: View limit in NPM/NCM setup
Hi sja, In account settings, you can set NCM role to None: Regards,Jiri
View ArticleRe: Orion Network Configuration Manager v6.1 does not have the...
Jiri, Sorry I missed your message. I was able to resolve the issue by upgrading NCM/NPM to the current version which has "SolarWinds.FIPSManager".
View ArticleClik here to view.
Re: Where can I get a device template for a Cisco ASA 5520 that will give me...
Sixmill, It worked! Thanks for your help.
View ArticleRe: HP (formerly 3Com) v1910 / v2928 PoE Switches
Can this solution be used for CatTools for same device? If yes can I please be guided as to how?
View ArticleClik here to view.
Re: Standalone NCM v7 Question
Hi, What you can do is set maximum polling and status collecting intervals. (Edit node properties) All three input boxes above accept maximum value of 32767 (of the indicated unit). Regards,Jiri
View ArticleClik here to view.
Re: NCM connection with Cisco ME3600 switches
Hi mwill, If I understand you correctly, you are trying to test the connection details: What does the result of the test look like? Regards,Jiri
View ArticleRe: Running Vs. Startup config assistance requested - Comparison Criteria
Just closing the loop. Looking at your support case, I found out that resolution was to change the rule with the "quit" keyword to[ \t\r\n\v\f]*quit[ \t\r\n\v\f]* Jiri
View ArticleRe: Config change report does not ignore nvram or certificates
Hi sdeese, Sorry for the delay. I found out you had opened a support case for this problem.Could you please update this thread with the resolution once it's found? Thanks,Jiri
View Article