Clik here to view.
Re: NCM Policy for lines that are not exact matches?
ntp server (?!10.1.1.1).* This will find ntp server with any other IP address. Use this as a rule, alert critical if found.
View ArticleRe: NCM Policy for lines that are not exact matches?
That works. But, what if I'm looking for two servers? ntp server (?!10.1.1.1).*ntp server (?!10.1.1.2).*
View ArticleClik here to view.
Need advice with non-standard login.....
Looking for some advice on how to handle a non standard login... I have a few Nortel 470 switches in my environment. Some I can retrieve the config file from and some I can't. After looking into...
View ArticleClik here to view.
Re: NCM Policy for lines that are not exact matches?
ntp server (?!(10.1.1.1|10.1.1.2)).* or ntp server (?!10.1.1.(1|2)).*
View ArticleDeleted NCM Job by Mistake
I deleted a pretty detailed NCM job by mistake. I am not totally sure what the job completely consisted of or I would just rebuild it. It would be nice if I could somehow get the job back before my...
View ArticleRe: Save script output
I figured out how to use a Configuration Change Template to run a command(s) against many devices. Then I have an external script that looks through the transfer queue log table for a keyword I put in...
View ArticleRe: Config change report does not ignore nvram or certificates
I'm having the same issue - do you have a solution?
View ArticleRe: Config change report does not ignore nvram or certificates
I replied with the solution
View ArticleRe: Config change report does not ignore nvram or certificates
The solution for this was to basically stop looking for strings at the beginning of the line in the configs. Below is the reply from SW on how to fix my specific problems: Regarding you inquiry about...
View ArticleClik here to view.
Re: Config change report does not ignore nvram or certificates
Thanks!! I changed the rule for ignoring "quit" as you stated but the certificate was still being detected. So I removed all the "^" from each of the lines for certificate detection. That worked!...
View ArticleRe: Connection Refused by IP
Hi Holy,It's been a while and i want to tell that my problem is already resolved.Really appreciate your full support. Thanks and God blessAlex
View ArticleRe: Connection Refused by IP
Hi Holy,I discovered that our profile name (ncmadmin) at Solarwinds NCM and at our Cisco ACS is not match. So that make the device refused the connection.It is really my bad not to check it before.Once...
View ArticleClik here to view.
HCM: HP Switch Login Banner
Hey I have the same problem as descibed in this case:https://thwack.solarwinds.com/thread/18082 After the Login a Banner is shown on the HP Switch and you have to press "any key".But it seems like NCM...
View ArticleUnable to connect to remote polling engine when downloading 400+...
Anyone seen Unable to connect to remote polling engine <polling engine name>. Verify that this engine is running and retry your operation. This occurred when downloading over 400 router...
View ArticleNCM-how to get daily email of who made what changes
Does anyone know how to get a daily email of who did what changes through NCM? I get daily change logs which highlight changes , but it doesn't show who made what changes. There's also an audit report...
View ArticleClik here to view.
How are others out there using NCM to manage ACLS? I am just curious.
I am just curious how others are using NCM to manage ACLs. Looking for idea to improve. We are using snippets and even though we have sequence numbers, we are still uploading the entire ACL when we do...
View ArticleNCM Nightly Config Backup Job Every 1 Day(s) vs. Every Week Day
I'm evaluating NCM. I'm using the canned Nightly Config Backup job to backup my network device configs. I keep selecting the radio button for Every 1 Day(s), because I want backups on Saturday and...
View Article