Re: Looking for help on getting solarwinds to stop saving the config when the...
Hmm... Its possible. I found this note on a posting on a Cisco site: "Note: When the tftp-server command and the filename are defined, every time the write net command is issued, the current...
View ArticleRe: Looking for help on getting solarwinds to stop saving the config when the...
We have TACACS installed and running but I haven't added the line above like you mentioned yet. I Switched the device template from Cisco Adaptive Security Appliance to Cisco IOS. It seems to download...
View ArticleRe: Looking for help on getting solarwinds to stop saving the config when the...
How is your ignore commented lines configured? I think the "out of the box" configuration for that doesn't work right. My regex pattern is "^:" which seems to work for me I believe... I might have...
View ArticleClik here to view.
Re: Looking for help on getting solarwinds to stop saving the config when the...
It's the same, i have a ^! and a ^: line to get both times of commenting!
View ArticleRe: WLC 5508 Backup using NCM V7.4
Hi cnorborgStill have issue, should have tagged as Helpful not Correct .Newbie mistake.
View ArticleClik here to view.
Re: WLC 5508 Backup using NCM V7.4
Can you telnet to your WLC? Make sure your settings are correct in NPM and click on the Test button to make sure it connects as per the image below.
View ArticleRe: WLC 5508 Backup using NCM V7.4
Thanks superfly99That fixed it. Need to change Enable Level: to <No Enable Login>.
View ArticleRe: Service account
Or are you talking about NCM? You do this in Settings, NCM Settings and then either select Global Device Defaults or Connections Profiles depending on which one you want to change.
View ArticleNCM: is "UseVirtualPromptForCommands" an undocumented command?
Hi I just spent a few hours Troubleshooting a Config Change Template which took almost 2 minutes time to configure two simple access interfaces on a Switch. (it's not a Cisco Switch)in the device...
View ArticleRe: NCM: How to change more than one interface in one go?
Thanks for your Input. I see what you mean: putting CDP Information as description to an interface, but I'm after something different.I need to add a description (e.g. a server name or asset...
View ArticleClik here to view.
Re: Looking for help on getting solarwinds to stop saving the config when the...
Just double checking, in the Comparison Criteria table of what you're ignoring, the Enabled column is set to "Yes" by both of these rules? Your sure there are no spaces or anything after the "^:" that...
View ArticleClik here to view.
Clik here to view.
Monitor HP 4120 IP Phone
I have been trying to monitor our HP 4120 in Solarwinds and no luck. beside using ICMP to the IP of the phone they will not respond to any SNMP. HP passed me around the Support ring with no help on an...
View ArticleRe: Looking for help on getting solarwinds to stop saving the config when the...
Yep by default i have it set. It properly ignores the lines while active but my concern was with the fact solarwinds keeps writing the config - even when using the copy command. I'm not sure at this...
View ArticleClik here to view.
Re: Looking for help on getting solarwinds to stop saving the config when the...
Reaching a bit here, not sure what is going on. It almost sounds as if you have it set up to keep copies of configs whether or not if they've changed or not. That is assuming your "Comparison...
View ArticleRe: Verify Configuration register using Compliance Reports
I can think of a couple ways to do this, but neither one uses the Compliance manager. The problem is that at least currently, the compliance manager only uses the configurations that NCM downloads for...
View ArticleRe: Looking for help on getting solarwinds to stop saving the config when the...
First, let me say Craig, thank you for continuing to help me out here. I greatly appreciate it! Second, the Settings" / "NCM Settings" / "Real Time Change Detection" / "Config Downloads &...
View ArticleRe: Looking for help on getting solarwinds to stop saving the config when the...
Hmm... Yes, AFAIK there is no way to have Orion save a copy of a config that it considers to not have changed, at least within RTCD. So, if it is writing a config that would mean that it either...
View ArticleRe: Verify Configuration register using Compliance Reports
Thanks for your help. I ended up creating a script using show version | i Configuration register Thanks Craig. I then ran a job using the script and dowloaded the log file. Thanks
View ArticleRe: Looking for help on getting solarwinds to stop saving the config when the...
Thanks Craig! I will get the auditing enabled asap and report back.
View Article