Re: ＮＣＭ >設定 >ノード編集 > Connectionのテスト > Connection Profile > Testで失敗する
Hi Mikio, Please open a support case then. Regards,Jiri
View ArticleRe: ＮＣＭ >設定 >ノード編集 > Connectionのテスト > Connection Profile > Testで失敗する
Hi Jiri-san, Thank you for your response. Yes, open a support case.Best Regards, Mikio Haragakiuchi
View ArticleClik here to view.
Clik here to view.
Does NCM 7.4 have a report that shows the last time an interface passed traffic?
In earlier versions of NCM I could discover network switch ports which had been unused for extended periods by using the NCM application on the server instead of via the web interface. Click on the...
View ArticleRe: NCM Jobs List??
Does not look like you have solarwinds admin rights. Just off the top of my head.
View ArticleClik here to view.
Re: NCM compatibility
NCM 7.3.1 Cisco SG300-10Cisco SG300-10P both work fine under NCM without customization; I don't have any SG200's Richard
View ArticleRe: "Automatically execute this script when violation is found" Compliance...
Hi Tony, yes we created a job for every siingle report. We have 9 active reports and 9 jobs for each report. The jobs start with a gap of 30 minutes to the next. The jobs run every day. Otto
View ArticleChange interface description depending on old descriptions
Hi! Im working on this piece of a pussle... We are going to change the configuration on 200+ switches to have the same standard conf, and one part of this is to rename all the interfaces accordingly....
View ArticleRe: "Automatically execute this script when violation is found" Compliance...
And the Report is enabled also?
View ArticleRe: Trunk interface and their own mac address.
I could be wrong, but are you overthinking this a bit? This SWQL query does what I think you want, can be customized quite easily... SELECT I.Node.Caption AS Device, I.Node.IPAddress, I.Caption AS...
View ArticleRe: "Automatically execute this script when violation is found" Compliance...
Hi Otto,If you have the NCM approval system enabled can you check that the "bypass approval system for automatic remediation of policy violations" is checked under "Settings-> NCM Settings->...
View ArticleRe: Trunk interface and their own mac address.
I like the simplicity of Craig's suggestion. If I were doing this, I'd probably build a Report to show exactly that same information. That's something nice about NPM--it gives you the flexibility to...
View ArticleClik here to view.
NCM- Realtime Config Change Detection- Usernames Not
Hello Im fairly new to solarwinds RTCD so excuse me if this is a simple fix but we have successfully configured our Cisco ASA's and Catalyst 3850 switches to send their RTCD updates to our Orion...
View ArticleClik here to view.
Re: Installing NCM on second polling engine
OK, we have the software on both the primary and secondary pollers updated with the exception of NTA, we will be doing that one next. We have installed on the second poller the bundle of additional...
View ArticleRe: Installing NCM on second polling engine
It looks like there's something broken -- will you please open a support case? Jiri
View ArticleClik here to view.
Re: Change interface description depending on old descriptions
I actually think this would be much easier to do with Compliance checking and config blocks... Have it search for a config block that looks for something that starts with "^interface (Fast|Gig)Ethernet...
View ArticleRe: NCM Jobs List??
That was it!, I have admin rights but I completely forgot that there is more custom settings you have to look through, including ncm. Now I can create jobs, etc. Thanks!
View ArticleRe: "Automatically execute this script when violation is found" Compliance...
Hi Tony, thanks a lot, I think the last one was the solution. We didnt have enabled the Point "Bypass approval system for automatic remediation of policy violations" I enabled it right now and will...
View ArticleCommand Script Output
Hi, May be this question is asked before ,i want to execute daily script on some devices and put the result in c:\Jobs\${NodeCaption}\${Date}.txtSo every days , the script output will be added to a...
View ArticleClik here to view.
Re: NCM Jobs List??
No worries, I was puzzled when i couldn't create the jobs or manage nodes through NCM too Glad I could help ^^
View Article