Re: Real-time detection not working
Hi Tim, I was reviewing this thread because I am having an issue where realtime detection is not working on devices that are on our secondary poller. I noticed in this thread you asked if the device...
View ArticleRe: Cisco ASA IPS Configuration Download
I would look to increase your SSH/Telnet timeouts for both the connection and the prompt. You can find these in the web console in any NCM 7.1 and above under Settings->NCM Settings->Protocol...
View ArticleRe: Can "request approval" be bypassed for certain scripts, for scripts which...
NCM cannot currently differentiate between the commands that are entered for an execute command script. Since you are using config change approvals, all execute commands scripts, even show commands,...
View ArticleClik here to view.
ncm 7.2.0 to 7.2.2 fails. no longer able to access NPM page or any orion apps
it the beginning i had NCM and NPM on the same server. Support told me to separate them for performancei did and it works now with NPM 10.7 and NCM 7.2, they told me to place them on the same server i...
View ArticleRe: Juniper SA / MAG SSL VPN config backup - is there a way with NCM
Well - we are at 7.2 and this still does not work!! Any ideas?
View ArticleNCM Regular expression to ignore "state up" or "state down" for node in the...
I have tried the following with little success ^[ \t\r\n\v\f]state[ \t\r\n\v\f]*^[ \t\r\n\v\f]state[ \t\r\n\v\f]*down^[ \t\r\n\v\f]state[ \t\r\n\v\f]*up^! state^! state*
View ArticleClik here to view.
Socket Connection aborted when trying to run config change template?
I have ran this particular config change template successfully before, however when I try to run it now I keep getting this error?
View ArticleRe: Using Config Change Script to Identify Switch Interface Mode
I'm searching too for a way to cycle through 3750 switch stacks to find the 'switchport mode access' interfaces and apply QOS settings avoiding the trunks. This would be across a large campus. Any...
View ArticleCan NCM job scheduler only use AD accounts for jobs? Not able to use SW Admin?
I'm using NCM 7.1.x with partial Win32 functionality and part web console. the job scheduler only allows me to use my AD account? does the scheduler only use Windows logins? not Solarwinds accounts?
View ArticleNCM Block Text Expressions
We have a section of config in our routers and switches that should be consistent across all nodes, and it VERY large. I have tried just copying and pasting the 100 lines or so into a text block in...
View ArticleI need to get real time change notifications for our Juniper Netscreen...
Devices Juniper SSG500 What is the best way of doing this please using this product (NCM 7.3). The downloading of configs is already working. Should I use syslog or snmp traps and what additional...
View ArticleRe: Cannot download running config - timeout problems
Changing this to 5 simultaneous sessions seems to have done the trick, thanks!
View ArticleCisco Nexus Serial number
We are trying to find a way to pull the serial number for Cisco Nexus 5548 devices as well as other Nexus products via SNMP. NCM currently uses the entity mib to pull serial numbers and this doesn't...
View ArticleClik here to view.
Executing scripts with NCM
I am trying to apply some common configurations to multiple switches by using a script (e.g. set user account, NTP server, disable a port) I have created a job to run simple commands to verify that the...
View ArticleClik here to view.
Re: Cisco Nexus Serial number
Ok after a lot of research and a back forth with Solarwinds support, the Nexus devices store the serial number in a different place in the mib than other Cisco devices. Solarwinds has not cracked the...
View ArticleConfiguring real-time detection on Nexus switches
Hi, I'm wondering how users are configuring their Nexus 5k/7k switches for enabling real-time detection? I have realtime detection enabled via syslog for my Catalyst router/switches and that works....
View ArticleCustom Property issue in Custom Query SWQL
Per the documentation, SELECT Caption FROM Orion.Nodes WHERE Node.CustomProperties.City = 'Atlanta' Should work in a custom query object, but instead I get 'there was an error in querying the...
View ArticleClik here to view.
Re: NCM Block Text Expressions
Hi Jim, I don't think you can paste multiple lines in that way and get it to work. I suspect that newline characters are the root of why they don't match. There is a "canned" rule that uses RegEx and...
View ArticleRe: Executing scripts with NCM
That error of "No devices to run job on this engine." This is a known bug with NCM 7.2 and 7.2.1: This bug is resolved in 7.2.2.
View ArticleClik here to view.
Re: Transfer Status stuck
I have the same problem. My jobs have been stuck for several days and new jobs are not running
View Article